Gevora Hotel Dubai: 8K Mirror Stainless Steel Interior Metalwork

Across the lobby, elevator areas, meeting rooms, restaurants and pool deck, Xinmao Metal supplied 236 metal components with a combined developed area of 186 m². The package ranges from reflective wall panels and fine trims to patterned restaurant screens and the pool railing. Each part belongs to the same hotel, but the material choice changes with its location.

The defining finish was 8K mirror stainless steel. In hospitality interiors, that finish has little room for error. It reflects light, movement and the materials beside it. Any waviness, scratch or uneven joint can be seen immediately, especially around elevators and reception areas where guests pass close to the walls. The project therefore depended on surface protection as much as fabrication: components had to arrive with the intended reflection and retain it through installation.

Lobby and elevator metalwork for close viewing

In the controlled interior areas, the mirror panels were made from 1.5 mm grade 201 stainless steel, a cost-conscious choice for this project. Four panels at the elevator lobbies each reached up to 5 m². At that scale, reflected lines make any waviness or uneven joint easy to see, so setting-out and handling matter as much as the polished face.

At elevator openings, mirror cladding must also respect the lift manufacturer's door clearances and service requirements. Large mirror faces need backing, returns, reinforcement and adjustable fixings so the installed plane is not distorted by an uneven substrate. Field grinding on a finished mirror face should be avoided because local reflection recovery rarely matches the surrounding panel.

The lobby is where the finish receives its closest inspection. Reception counters, seating, wall panels and elevator entrances are seen from several directions, often under both daylight and downlighting. The mirror stainless steel details in this project were used to frame those high-visibility surfaces, giving them a more precise edge and a stronger relationship to the hotel’s polished stone and glass.

Elevator lobbies present a particular challenge. Repeated vertical panels need to remain aligned over a long wall, while lift doors, call buttons and surrounding stone introduce several small interruptions. Metal wall cladding must account for all of them. The final surface should read as continuous even though it has been divided for manufacture, access and installation.

The mirror surfaces received a glossy anti-fingerprint finish to make handling marks less visible in high-contact areas while retaining the bright reflection.

How the anti-fingerprint finish works. The mirror surface is finished first, then a thin, transparent anti-fingerprint (AFP) layer is applied over it. This top layer lowers surface energy, making skin oils and moisture less likely to spread or adhere. It makes routine cleaning easier, but it does not make the surface scratch-proof; a soft cloth and a mild cleaner are still appropriate for care.

Meeting rooms that need more than a plain wall

The meeting-room package called for the same care at panel edges and openings. For coloured components in this project, Xinmao welded pre-coloured sheet rather than coating a completed assembly afterwards. That sequence reduced finishing cost, while leaving the team to control weld and joint appearance during fabrication.

Conference rooms are usually planned around function: sightlines, lighting, screens and furniture layouts. The Gevora Hotel package gave these spaces a more finished architectural layer through metal wall surfaces, ceiling details and decorative lighting. The aim was not to make every wall reflective. It was to place metal where it could organise a room, mark a perimeter and catch the light in a controlled way.

Large metal wall panels need a consistent setting-out strategy. A room can look calm only when the panel grid, ceiling breaks and door openings acknowledge one another. For mirror-finished stainless steel, this is especially important because reflected lines exaggerate any misalignment. The fabrication and installation team therefore need to treat each panel as part of a sequence rather than as an independent sheet.

The same principle applies to the conference-room chandeliers and ceiling details. Metal carries the visible support and provides a finish link between wall surfaces and overhead elements. Lighting then brings the material to life without turning the room into a display of reflection. This balance is what lets a meeting room feel suitable for formal events while remaining comfortable for daily use.

CNC aluminium screens in the restaurant

For CNC aluminium screens, the pattern file must be checked for minimum webs, bridge widths, panel thickness, frame depth, finishing sequence and fixing method before cutting starts. Slender cut edges can distort during handling or coating, especially on large panels. At interfaces with stainless steel or carbon-steel support members, wet or frequently cleaned locations may require non-conductive isolation and drainage so dissimilar-metal contact does not create staining or galvanic-corrosion risk.

The restaurant screens took a different approach. They were cut from 10 mm aluminium plate and finished with powder coating. Aluminium kept these substantial patterned panels lighter than an equivalent stainless steel plate, so the screens could define dining areas without adding another reflective wall.

The restaurant images show this approach around buffet and café settings. The screen pattern adds texture, while the metal frame keeps the room ordered. It is a practical choice where guests need visual separation but staff still need an open operational layout. The aluminium component also avoids forcing one material and one finish into every part of the hotel. The project uses mirror stainless steel where reflection and precision are needed, then uses CNC aluminium where pattern and permeability are more useful.

Pool, dining and the value of a coordinated package

The pool railing faced outdoor conditions that the interior panels did not. Its material therefore had to be considered separately from the grade 201 mirror sheet used inside.

For this project, the pool railing was made from grade 304 stainless steel. Before shipment, its sections were assembled at the factory so the team could check dimensions, hole positions, joints and flatness together. That check helped the pieces arrive at site ready to fit the agreed layout.

Records that support final acceptance

The handover file should link installed modules to their approved drawings and inspection records. Depending on the scope, it can include material certificates, signed finish samples, panel numbering, dimensional checks, pre-assembly photographs, fixing inspections and approved site-adjustment records. Structural, fire and acoustic claims must relate to the engineered or tested full assembly, not to the visible sheet in isolation.

The Gevora package works because each material was assigned to a specific setting: mirror-finish stainless steel for close-viewed interior surfaces, powder-coated aluminium for the restaurant screens, and a separately fabricated railing for the outdoor pool. The factory checks and fabrication sequence give the case more substance than the finish names alone.